Brick Paver Installation & Edging



Staging of material

Most paver tasks will vary depending upon access, website conditions, project size and naturally, the weather. These scenarios can have a general influence on your job from a timing stand point. Mindful consideration needs to be taken to figure out the time to start the paver installation. Constantly try to avoid any traffic or decrease on the prepared locations.

The foreman or job supervisor ought to constantly have the materials (sand/ pavers) distributed around the task site for easy and efficient setups. Paver pallets/bundles should be put in a way not to interfere with the paver installation. The proper pallet/bundle placement can make the real task installation simpler and quicker by lowering the overall labor of dealing with the product.

Brick paver patterns

Pavers can be placed in many different patterns depending on their shape. Each paver shape will usually have numerous various hatch patterns that are supplied by the manufacturer.

Specialists require to take into consideration the traffic weight loads on their paver tasks. In a lot of applications worldwide, it has been revealed that pavers laid in a herringbone pattern have actually performed effectively.

Pavers that are 60 mm (2 - 3/8 in) density appropriate for pedestrian applications. Pavers that are going to be used in industrial or commercial applications must be 80 mm (3 - 1/8 in) in density.

Reference/starting point for brick paver installation

There are a number of conditions that determine the beginning point of a paver task.

When starting to set up pavers it is best to snap a real straight chalk line on the surface of the bedding sand or pull a true straight string line above the surface of the bed linen sand at the ended up elevation of the pavers This will help as a guide for maintaining straight joint lines and will also enable the installer to make changes in the alignment of the pavers.

Buildings and concrete curbing are normally not straight and need to not be utilized for establishing straight joint lines. The usage of string lines is essential to determine the true straightness of the edge. As the paver installation advances, the string lines will assist decrease the requirement for small trim pieces.

These will maintain a minimum joint width and permit the bed linen and jointing sand to enter between each paver. Pavers with spacer bars are typically not laid in snug against each other because a string line will offer consistent joint spacing.

Installation of brick pavers.

One of the most commonly utilized techniques for the installation of pavers is hand installation of each paver. It is best to install a single row of pavers along one of the true straight lines that you have pulled or above the bedding sand. The best method is to place a paver against another one and let it slide down into the bed linen sand.

When setting up pavers on a high grade, they need to be set up at the base of the grade going uphill. This will avoid the pavers from sneaking as they are being laid.

On large commercial and industrial applications, hand laying pavers would not be cost effective due to the labor intensity. The best method for setting up pavers on big tasks is to install them mechanically. Using a mechanical laying device can install roughly 6000 - 7000 sq ft a day. There are a couple items a contractor should consider prior to setting up pavers mechanically:

1.) Mechanical installers are only efficient in setting up pavers in particular patterns.

2.) The professional should make sure that the manufacturer can production and bundling pavers in the preferred pattern on the pallets for easy mechanical installation.

3.) Contractors might come across a color mixing circumstance coming off the bundles of pavers Poor color mixing might lead to a patchy looking installation. Many manufacturers follow color mixing on each package of pavers, but it is the contractor's duty to make sure appropriate blending in the field.

Cutting treatments for brick pavers.

Contractors normally have 2 ways of cutting pavers. When cutting pavers damp, it will help minimize dust and will extend the diamond blades life. The operator of the brick saw need to constantly cut the pavers away from the surface of the paver field when cutting damp, due to the truth that the pavers will create a slurry that will stain the paver surface area.

The brick saw operator ought to always use the proper defense that is needed for operating a saw, such as eye, ear, breathing and hand protection ).

Edging types

Edge restraints play a significant function in the overall success of an interlocking pavement installation Edging restraints remove lateral movement of the pavers and hold the pavers securely together. Particularly at the outer boundary of the paver application, without an edging restraint, your project is ensured to fail with time.

There are a number of different edging restraints from which professionals can choose. Normally produced edge restraints are the most frequently used by specialists. Produced edging restraints can range from, plastic edging, steel and aluminum, woods or precast concrete and stone. An edging type that is utilized mainly in business and industrial applications is poured-in-place concrete curbs. This edging restraint is normally installed by other specialists.

Edging installation.

This could result in the migration of the bedding sand and ultimate lateral movement of the pavers. If there is a possibility of losing bedding sand in between the pavers and the edge restraint, then geo textile fabric is suggested. When a space between the pavers and the edging surpasses 3/8" (10mm), then the area should be filled with cut pavers.

Compaction of brick pavers.

After installation, the pavers need to be compressed. The whole area that is to be compressed need to be swept clean of any foreign items and particles that can cause scratching or scuffing on the surface of the pavers.

It is necessary to have a compactor that can exert between 3000lbs. And 5000 pounds. Of centrifugal compaction force. In addition, it is important that the first compaction takes place before any jointing sand has actually been applied to the pavers. This can cause a bridging issue and will not permit the joints to be completely filled with jointing sand if jointing sand is applied to the pavers prior to compaction takes location. This can likewise prevent the pavers from being correctly set into the bed linen sand.

When compacting the pavers, it is suggested that you make a minimum of 2 passes in various instructions across the pavers. This will allow the pavers to be appropriately embeded in the bed linen sand and will require the bedding sand up Tree Service Del Ray Beach into the joints from the bottom of the pavers.

The compaction of the pavers is very important to the final performance of the pavers. Failure to do appropriate compaction can lead to contortions and pavement failure with time.


Paver pallets/bundles should be placed in a manner not to interfere with the paver installation. One of the most commonly utilized approaches for the installation of pavers is hand installation of each paver. The operator of the brick saw need to always cut the pavers away from the surface of the paver field when cutting wet, due to the truth that the pavers will produce a slurry that will stain the paver surface area. Edging restraints get rid of lateral motion of the pavers and hold the pavers securely together. When a space between the pavers and the edging exceeds 3/8" (10mm), then the space ought to be filled with cut pavers.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments on “Brick Paver Installation & Edging”

Leave a Reply

Gravatar